Elcometer Canadian Distributor

Elcometer 308 hygrometer

$806.50 CAD

• 12 months limited warranty
• Greater than 40 hours of battery life
• Designed for hot and humid weather
• Measurement hold/release function

Support, maintenance, calibration –
1 800 463-4363

 

The Elcometer 309 Delta T Hygrometer provides a reliable and fast measurement of the two critical climate parameters within coatings: Delta T & RH

Surface temperature (Ts) and Relative Humidity (%RH) are two key climatic values that are specified on many datasheets.

• Delta T (TΔ): The difference between the surface temperature (Ts) and the dewpoint temperature (Td). When TΔ is less than 3ºC (5ºF) painting should not occur.

• Relative Humidity (RH): Expressed as a percentage, RH is the ratio of the amount of water vapour actually held by the air compared to the maximum amount of water vapour the air could hold at a given temperature. Typical maximum RH values specified by paint manufacturers are between 75% and 85%.

The Elcometer 308 Hygrometer provides a simple and fast measurement of these two critical parameters.

Rugged design: Suitable for use in extreme environments the Elcometer 308 Hygrometer is dustproof and waterproof with fully sealed sensors.
Measurement Hold / Release function: With a single button press reading is ‘held’ on the screen. These can then be recorded before simply pressing the button again to ‘release’ the screen and continue to take further readings as necessary.
Backlight: Bright screen making information easy to read – ideal in dark or confined spaces.

This Hygrometer can also be used in very hot environments where the surface temperature of the substrate can exceed the paint manufacturer’s recommended limits for successful painting.

Before painting it is necessary to check that the climatic conditions are suitable for the coating being applied. These are clearly specified on the paint manufacturer’s product data-sheet.

One of the best hygrometers available in Canada and the world

Operating Range -4 to +176°F (-20 to +80°C), 0 to 100% RH
RH Accuracy ±3%
Resolution 0.1°F (0.1°C) / 0.1%
Power Supply 2 x AA 1.5V Batteries or via USB Cable
Battery Life Greater than 40 hours (Backlight off)
Dimension 7 x 3 x 1.4″ (180 x 75 x 35mm)
Weight 10.6oz (300g)
Certificate available Certificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability
Packing List
  • Elcometer 308 Hygrometer
  • wrist strap
  • 2 x AA batteries
  • protective pouch with belt clip
  • RH & surface probe calibration certificate
  • operating instructions

Before painting it is necessary to check that the climatic conditions are suitable for the coating being applied. These are clearly specified on the paint manufacturer’s product data-sheet.

Product Accessories

Protective Carry Case / Pouch – (T99921192)
USB Cable – (T99921325)

QUICK TIP:

How to use Elcometer 308 to obtain a reading:

1. Press the ON/OFF key
2. To display Ts press the Ts softkey
3. Select °C/°F as required for Ts reading
4. Place gauge in the environment and if required the surface
temperature
5. Wait for reading(s) to stabilize
6. Press Hold softkey (II)
7. Review reading(s)
To take another reading press release button ( ) and
repeat steps 4-7

More information here:

Download Data Sheet
Download Instruction Manual

 

1-Free-shipping

Elcometer 116A Whirling Hygrometer | Metric (øC) |

Elcometer 309 Delta T Hygrometer

Elcometer 116C Sling Hygrometer

 

 

The Elcometer 309 Delta T Hygrometer provides a reliable and fast measurement of the two critical climate parameters within coatings: Delta T & RH

Surface temperature (Ts) and Relative Humidity (%RH) are two key climatic values that are specified on many datasheets.

• Delta T (TΔ): The difference between the surface temperature (Ts) and the dewpoint temperature (Td). When TΔ is less than 3ºC (5ºF) painting should not occur.

• Relative Humidity (RH): Expressed as a percentage, RH is the ratio of the amount of water vapour actually held by the air compared to the maximum amount of water vapour the air could hold at a given temperature. Typical maximum RH values specified by paint manufacturers are between 75% and 85%.

The Elcometer 308 Hygrometer provides a simple and fast measurement of these two critical parameters.

Rugged design: Suitable for use in extreme environments the Elcometer 308 Hygrometer is dustproof and waterproof with fully sealed sensors.
Measurement Hold / Release function: With a single button press reading is ‘held’ on the screen. These can then be recorded before simply pressing the button again to ‘release’ the screen and continue to take further readings as necessary.
Backlight: Bright screen making information easy to read – ideal in dark or confined spaces.

This Hygrometer can also be used in very hot environments where the surface temperature of the substrate can exceed the paint manufacturer’s recommended limits for successful painting.

Before painting it is necessary to check that the climatic conditions are suitable for the coating being applied. These are clearly specified on the paint manufacturer’s product data-sheet.

One of the best hygrometers available in Canada and the world

Operating Range -4 to +176°F (-20 to +80°C), 0 to 100% RH
RH Accuracy ±3%
Resolution 0.1°F (0.1°C) / 0.1%
Power Supply 2 x AA 1.5V Batteries or via USB Cable
Battery Life Greater than 40 hours (Backlight off)
Dimension 7 x 3 x 1.4″ (180 x 75 x 35mm)
Weight 10.6oz (300g)
Certificate available Certificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability
Packing List
  • Elcometer 308 Hygrometer
  • wrist strap
  • 2 x AA batteries
  • protective pouch with belt clip
  • RH & surface probe calibration certificate
  • operating instructions

Before painting it is necessary to check that the climatic conditions are suitable for the coating being applied. These are clearly specified on the paint manufacturer’s product data-sheet.

Product Accessories

Protective Carry Case / Pouch – (T99921192)
USB Cable – (T99921325)

QUICK TIP:

How to use Elcometer 308 to obtain a reading:

1. Press the ON/OFF key
2. To display Ts press the Ts softkey
3. Select °C/°F as required for Ts reading
4. Place gauge in the environment and if required the surface
temperature
5. Wait for reading(s) to stabilize
6. Press Hold softkey (II)
7. Review reading(s)
To take another reading press release button ( ) and
repeat steps 4-7

More information here:

Download Data Sheet
Download Instruction Manual

 

1-Free-shipping

Elcometer 116A Whirling Hygrometer | Metric (øC) |

Elcometer 309 Delta T Hygrometer

Elcometer 116C Sling Hygrometer

 

 

Questions / comments: